Factory-direct bridal jewelry, shipped to the USA

Necklaces & Pendants

Necklaces & Pendants B2B: AQL, Tray Checks and What a QC Report Should Say

9 November 2026 · 10 min

Step 01

AQL, Tray Checks and What a QC Report Should Say

Two buyers ordered the same necklaces and Pendant in the same month. One paid 9% less and absorbed 23 rejects out of 420 pieces; the other paid our quote and shipped clean. The difference was clasp fatigue, and it was measurable on both benches.

The defect did not surprise us. clasp fatigue is the predictable output of a run where nobody wrote the tolerance down, and it is the first measurement we take on an incoming necklaces and Pendant. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Necklaces & Pendants wholesale product photo from the HOLYCOME line in Wuzhou

We did not discount the quote. We changed the gauge, the seat cut, the plating log and the tray rule, and the second run shipped with zero rejects on clasp pull strength and chain length within +/-3 mm. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Step 02

What North American buyers Check Before They Sign

Price is the first thing compared and the last thing that matters. These four measurements decide the return rate on necklaces and Pendants, and three of them cost nothing to specify. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Clasp Fatigue on necklaces and PendantsInspected visually at the trayGauntlet check on every piece, limit written in the specReturns inside 60 days of wear
Link Stretch on necklaces and PendantsBatch dependent, not loggedThickness and tension logged per lotComplaint after the second season
Pendant Bail Shadow on necklaces and PendantsEstimated from nominalGauged per size with go/no-go toolsResize queue and reship cost
Tolerance stack-up on necklaces and PendantsQuote states nominal onlyWorst-case band published per SKUFreight and duty drift

None of these are premium features. They cost seconds per piece and they remove the reason a buyer has to inspect twice. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Step 03

Where USD 26-180 Per Piece Actually Goes

The cost of a necklaces and Pendant in the USD 26-180 band splits roughly as below. The line buyers challenge most is labor, and it is the line that decides whether the piece survives a season. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Necklaces & Pendants close-up of setting and finish, HOLYCOME factory sample
Cost lineShareWhat moves it
Base metal or alloy for necklaces and Pendants34%Alloy choice and casting yield
Stone or melee for necklaces and Pendants25%Sieve range and lot batching
Setting and finishing labor for necklaces and Pendants22%Jig design and bench minutes
Plating, polish and QC for necklaces and Pendants15%Per-tray versus per-piece checks
Packaging and freight for necklaces and Pendants4%Box grade and DDP versus FOB

If a supplier will not break out the five lines above, the number you are comparing is not a price. It is a total that somebody else assembled from assumptions. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Step 04

The Three Failures We See Most in Incoming Samples

clasp fatigue

A spring clasp rated by catalog rather than by pull test opens after 40-60 wear cycles. The rating belongs on the spec sheet, not on the website.

Our countermeasure is a gauge and a written limit. It adds about 16 seconds per piece and removes the defect from the run rather than from the carton.

link stretch

Chain stretch starts at the link join where the wire was drawn thin to save metal. Measuring wire diameter at both ends of a run catches it before shipping.

In a 420-piece run this typically shows on 14 of pieces. Catching it means measuring clasp pull strength at the tray level, not inspecting the finished carton.

pendant bail shadow

A bail plated in a separate barrel than the chain shows a different white tone under store light. Plating a set in one barrel is the fix.

The commercial effect is clasp replacement plus a goodwill credit, typically USD 7-12 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return.

Step 05

AQL, Tray Checks and What a QC Report Should Say

The short version for necklaces and Pendants: it is arithmetic, not relationship. The long version is below.

One practical note on timing for necklaces: the calendar starts when the spec is signed, not when the deposit clears. A buyer who signs in week one and pays in week three gets the goods in week five.

We date the necklaces and Pendants proforma from signature for that reason, and we state the deposit deadline in the same email that carries the spec sheet.

Step 06

How a Repeat Order Gets Built

Our process is deliberately boring, because boring is what survives a bulk run with several sets of hands on it. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

  1. Spec sheet signed before casting: cable, tolerances, plating thickness and packing format.
  2. Sample in 3-5 working days from stock components, or about 20 days if a new model is required.
  3. Production photos at three checkpoints: raw cast, post-polish, post-set, with buyer approval at each.
  4. Bulk in 15-20 days under 500 pieces; custom tooling runs 25-30 days.
  5. Pre-shipment QC report with per-tray counts and a retained reference tray for disputes.

A first order at 50 pieces per design is a measurement rather than a purchase. It tells you what clasp pull strength and chain length within +/-3 mm looks like from this line. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Step 07

What a Report Proves and What It Does Not

Buyers in US e-commerce tend to over-index on unit price for necklaces and Pendants and under-index on what happens after delivery.

There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on necklaces and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly.

We would rather lose a first order of necklaces on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high.

Step 08

How the Second Order Becomes Cheaper

Most necklaces and Pendants disputes we arbitrate trace back to this line, not to the defect itself.

We run this check per tray rather than per carton because the defect that matters on necklaces is the one that repeats. A single odd piece is noise; a pattern across one tray is a process problem and it will be in every tray made after it.

The report the buyer receives states the count per tray, the measured average and the outlier count for necklaces and Pendants. It is deliberately unglamorous, and it is the document that settles most disputes before they start.

Step 09

What the Quote Actually Covers

For necklaces and Pendants at this price band, the honest answer is a range rather than a point, and the range has a reason.

In US e-commerce terms, this is the difference between a landed cost the buyer can plan against and a number that moves after the container ships. For necklaces, we publish the figure per SKU and hold it for the order window rather than for the calendar year.

Practically, it shows up in three places for necklaces: the proforma, the QC sheet and the credit note if something goes wrong. All three should quote the same number. When they do not, the argument is about paperwork, not about the product.

Step 10

What This Means for a First Order

A test run at 50 pieces tells you three things: whether clasp fatigue is controlled, whether packing survives freight, and whether the count is honest. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Buyers who run that measurement before committing a season usually keep the supplier. Buyers who skip it usually pay twice for the same lesson. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Step 11

Freight, Duty and the Arrival Check

We ship from Guangzhou or Shenzhen, and the port choice follows the carrier rate rather than a fixed habit. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

DDP is available for US accounts that want duty and clearance on our side, and it removes the invoice that arrives after the carton clears. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

On arrival, weigh a tray and measure ten pieces. Anything outside the band is a claim with evidence rather than a difference of opinion. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

Step 12

Frequently Asked Questions

What is the minimum order for necklaces and Pendants?

50 pieces per necklaces and Pendant. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 we cannot keep the gauge check independent of the shift, which is the part buyers actually pay for on necklaces and Pendants.

How long does a reorder of the same necklaces and Pendant take?

12-15 days for necklaces and Pendants, because the model, the gauge set and the signed spec stay in our system. A first run is longer: 3-5 days for a stock-component sample, about 20 days if a new model is needed, then 15-20 days for bulk under 500 pieces.

Do you supply certificates for necklaces and Pendants?

stone and metal report per lot for necklaces and Pendants. Below that threshold we supply a batch report plus per-piece measurement of clasp pull strength, which is what most resellers need at the counter.

What finish do you use on necklaces and Pendants, and how thick is it?

Rhodium at 0.20 micron minimum on white necklaces and Pendants, with a palladium strike layer so wear-through reads white rather than yellow. Thickness is logged per lot and appears on the QC sheet, not only in the brochure.

How do you handle a rejected tray of necklaces and Pendants?

We replace or credit inside the same order cycle. The retained reference tray decides: if clasp fatigue shows on our retained necklaces and Pendant we own it, and if it appeared in transit we split the assay cost and file with the carrier. A typical exposure on necklaces and Pendants is clasp replacement plus a goodwill credit, typically USD 7-12 per piece.

Step 13

Next Step

If you are quoting necklaces and Pendants against another supplier, send that quote. We will mark the four lines where the numbers diverge and let you decide. It is written into the necklaces and Pendants spec sheet that travels with the quote, so the bench and the buyer read the same number.

The factory behind necklaces and Pendants here is Wuzhou HengliLai Jewelry Co., Ltd., operating since 2009 in Wuzhou, Guangxi, at roughly 60,000 pieces a month. Reach the export desk at service@holycome.com or +86 133 7744 7107 on WhatsApp.

Related reading: Earrings Wholesale: Carton Cube, Duty and the Freight Line That Surprises Buyers - HOLYCOME Engagement Rings B2B: What the Quote Actually Covers - HOLYCOME

Put this into a quotation

Send your spec sheet — stone, cut, size, plating and quantity — and we will return a costed timeline.

Ask the workshop

← Back to all articles

Related Jewelry Guides

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .