Factory-direct bridal jewelry, shipped to the USA

Earrings

Earrings Wholesale: Carton Cube, Duty and the Freight Line That Surprises Buyers

9 November 2026 · 10 min

Step 01

Carton Cube, Duty and the Freight Line That Surprises Buyers

A US independent jewelers and Shopify sellers sent us a competitor's earring in January with one question: why does this fail at prong geometry after a season. We measured it, rebuilt the spec around stone retention after a 40-cycle wear test and prong tip height within +/-0.10 mm, and shipped 120 earrings that cleared inspection with zero rejects.

That rejection was avoidable at the drawing stage. prong geometry belongs on the spec sheet next to the stone size, not in the claim email three weeks after arrival. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Earrings wholesale product photo from the HOLYCOME line in Wuzhou

Our rebuild kept the buyer's retail price and changed four numbers on the bench. The next run cleared inspection because the specification traveled with the tray, not with a phone call. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Step 02

What American buyers Check Before They Sign

Most quotes describe the earring and skip the part that determines the buyer's margin. Those four lines are listed below with the trade default beside our standard. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Prong Geometry on earringsInspected visually at the trayGauntlet check on every piece, limit written in the specReturns inside 60 days of wear
Rhodium Burn Off on earringsBatch dependent, not loggedThickness and tension logged per lotComplaint after the second season
Size Step Drift on earringsEstimated from nominalGauged per size with go/no-go toolsResize queue and reship cost
Tolerance stack-up on earringsQuote states nominal onlyWorst-case band published per SKUFreight and duty drift

Write these four into the purchase order and the argument after delivery becomes arithmetic rather than recollection. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Step 03

Where USD 38-210 Per Piece Actually Goes

Buyers assume the stone dominates the cost of a earring. At wholesale it is closer to a quarter, and the labor line is where two quotes for the same drawing diverge by double digits. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Earrings close-up of setting and finish, HOLYCOME factory sample
Cost lineShareWhat moves it
Base metal or alloy for earrings32%Alloy choice and casting yield
Stone or melee for earrings23%Sieve range and lot batching
Setting and finishing labor for earrings21%Jig design and bench minutes
Plating, polish and QC for earrings14%Per-tray versus per-piece checks
Packaging and freight for earrings10%Box grade and DDP versus FOB

The cheapest quote for earrings usually hides its saving in the plating line and the stone grade. Both show up in the second season, not the first. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Step 04

The Three Failures We See Most in Incoming Samples

prong geometry

A prong that grips the girdle instead of the pavilion survives the showroom and fails the third ultrasonic clean. The seat has to be cut to the pavilion angle before the prongs close.

The commercial effect is a return shipment plus a resize labor claim, typically USD 9-14 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return.

rhodium burn-off

A 0.05 micron rhodium layer reads white in the tray and shows yellow at the shank in six months of daily wear. Thickness, not bath chemistry, is the variable that matters.

Our countermeasure is a gauge and a written limit. It adds about 22 seconds per piece and removes the defect from the run rather than from the carton.

size-step drift

A run gauged at size 6 and estimated elsewhere ships a size 8 that measures 7.75. The mismatch shows up as a resize queue two weeks after launch.

In a 120-piece run this typically shows on 14 of pieces. Catching it means measuring stone retention after a 40-cycle wear test at the tray level, not inspecting the finished carton.

Step 05

Carton Cube, Duty and the Freight Line That Surprises Buyers

Ask three suppliers of earrings this question and you will get three answers. Only one of them survives an inspection.

There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on rings and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly.

We would rather lose a first order of rings on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high.

Step 06

How a Repeat Order Gets Built

The calendar below is what we quote on a 120-piece run of earrings. It starts when the spec is signed, not when the deposit clears. For earrings in this band the rule is the same on every tray of the run, not only on the first.

  1. Spec sheet signed before casting: lost-wax cast, tolerances, plating thickness and packing format.
  2. Sample in 3-5 working days from stock components, or about 20 days if a new model is required.
  3. Production photos at three checkpoints: raw cast, post-polish, post-set, with buyer approval at each.
  4. Bulk in 15-20 days under 500 pieces; custom tooling runs 25-30 days.
  5. Pre-shipment QC report with per-tray counts and a retained reference tray for disputes.

MOQ is 50 pieces per design, low enough to test a category and high enough to keep the casting line accountable. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Step 07

The Reject Tray Policy That Decides a Partnership

Most earrings disputes we arbitrate trace back to this line, not to the defect itself.

We run this check per tray rather than per carton because the defect that matters on rings is the one that repeats. A single odd piece is noise; a pattern across one tray is a process problem and it will be in every tray made after it.

The report the buyer receives states the count per tray, the measured average and the outlier count for earrings. It is deliberately unglamorous, and it is the document that settles most disputes before they start.

Step 08

MOQ, Mixed Designs and the Real First Order

For earrings at this price band, the honest answer is a range rather than a point, and the range has a reason.

The buyers who get the most out of rings treat the first order as a measurement, not as a purchase. They buy a small run, measure the four numbers that matter, and then commit.

We support it directly on earrings: a 50-piece test run per design, the same gauge standard as a bulk order, and the same retained tray. Small does not have to mean loose.

Step 09

AQL, Tray Checks and What a QC Report Should Say

Buyers ask it in the first call about earrings and rarely get a number they can put in a spreadsheet.

Three numbers decide it for rings: the tolerance band, the inspection density and the responsibility clause. Write all three down and the rest of the negotiation is arithmetic. Leave any of them out and it becomes a discussion about intent.

We send a one-page sheet with every earrings quote that states those three, plus the retained-tray rule. Buyers who compare on it usually find that the gap between suppliers is smaller than the gap between the specs they were comparing.

Step 10

What This Means for a First Order

The point of a small first run is not the margin. It is finding out whether the supplier's paperwork survives contact with the actual goods. For earrings in this band the rule is the same on every tray of the run, not only on the first.

The first order is the cheapest inspection a buyer will ever run, because the volume is small enough to check every tray by hand. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Step 11

Freight, Duty and the Arrival Check

Sea freight costs roughly a third of air and takes three times the transit, which only makes sense for an SKU already selling in US wholesale. For earrings in this band the rule is the same on every tray of the run, not only on the first.

FOB is the default and DDP is the option. Buyers new to US wholesale usually take DDP once and then switch after they see the breakdown. For earrings in this band the rule is the same on every tray of the run, not only on the first.

The arrival check is three steps: count cartons against the packing list, weigh a sample tray, and measure ten pieces against stone retention after a 40-cycle wear test and prong tip height within +/-0.10 mm. For earrings in this band the rule is the same on every tray of the run, not only on the first.

Step 12

Frequently Asked Questions

What is the minimum order for earrings?

50 pieces per earring. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 we cannot keep the gauge check independent of the shift, which is the part buyers actually pay for on earrings.

How long does a reorder of the same earring take?

12-15 days for earrings, because the model, the gauge set and the signed spec stay in our system. A first run is longer: 3-5 days for a stock-component sample, about 20 days if a new model is needed, then 15-20 days for bulk under 500 pieces.

Do you supply certificates for earrings?

IGI or GRA above 0.50 ct for earrings. Below that threshold we supply a batch report plus per-piece measurement of stone retention after a 40-cycle wear test, which is what most resellers need at the counter.

What finish do you use on earrings, and how thick is it?

Rhodium at 0.20 micron minimum on white earrings, with a palladium strike layer so wear-through reads white rather than yellow. Thickness is logged per lot and appears on the QC sheet, not only in the brochure.

How do you handle a rejected tray of earrings?

We replace or credit inside the same order cycle. The retained reference tray decides: if prong geometry shows on our retained earring we own it, and if it appeared in transit we split the assay cost and file with the carrier. A typical exposure on earrings is a return shipment plus a resize labor claim, typically USD 9-14 per piece.

Step 13

Next Step

Send one drawing or one competitor sample with your target landed cost. We answer with a tolerance sheet, a cost breakdown and a production calendar in two business days. For earrings in this band the rule is the same on every tray of the run, not only on the first.

HOLYCOME runs this line from Wuzhou, Guangxi, through Wuzhou HengliLai Jewelry Co., Ltd. Output is about 60,000 pieces a month across earrings and adjacent categories. service@holycome.com or WhatsApp +86 133 7744 7107.

Related reading: Bracelets & Bangles Wholesale: Alloy, Karat and the Cost of a Color Change - HOLYCOME Wedding Rings & Bands B2B: MOQ, Mixed Designs and the Real First Order - HOLYCOME

Put this into a quotation

Send your spec sheet — stone, cut, size, plating and quantity — and we will return a costed timeline.

Ask the workshop

← Back to all articles

Related Jewelry Guides

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .