Engagement Rings
Marquise Engagement Rings: Length-to-Width Ratio That Flatters
A buyer in Nashville told us she had one bride a year who asked for a marquise, and last year she had eight. The shape is coming back, driven by bridal Pinterest boards and by celebrities wearing long, narrow stones. Marquise is the shape that makes a finger look longest and slimmest, but it is also the shape most often returned for being "too pointy" when the length-to-width ratio is wrong. Stock the right ratio and the shape sells itself.
The length-to-width ratio that flatters
A marquise is measured length by width. The flattering range for bridal is 1.8:1 to 2.2:1. Below 1.7:1 the stone reads fat; above 2.3:1 it reads skinny and fragile. The GIA cut grading notes that elongated shapes should be judged on length-to-width ratio rather than a single cut score. We spec our marquise moissanite at 2.0:1 by default, which is the ratio that photographs longest without looking odd. If your shop stocks oval cuts, the same elongation logic applies; read our oval vs round on-hand guide.
Point protection: the reason marquise fails in the field
The two points of a marquise are the weak spots. They chip if they knock a counter. We ship every marquise with V-prongs at both tips, not flat prongs. Flat prongs rest on the point edge and can snap the tip off. V-prongs cup the point and protect it. A bezel setting is overkill for marquise because it hides the shape; V-prongs are the right compromise. This is the same protection logic we apply to emerald cuts in emerald cut moissanite bridal elegance.
How marquise sits on different finger widths
Marquise elongates the finger visually. On a short, wide finger it is the single most flattering shape we stock. On a long, slim finger it can look stretched and thin. For slim fingers we recommend sizing the marquise slightly wider (closer to 1.8:1) rather than longer. For wide fingers, go to 2.2:1. Stock both ratios and let the bride hold the stone to her finger in store.
Wedding band pairing for a pointed setting
A marquise solitaire sits low and pointed, so a straight band will not sit flush. Spec a notched or curved band that clears the points. Our curved wedding bands for irregular settings covers this in detail. If the bride wants a pavé band, keep the pavé micro so it does not catch on the marquise tips.
Why the shape is coming back now
Marquise was popular in the 1970s and 1980s, faded in the 1990s and 2000s, and has returned over the last five years. The driver is Pinterest: brides searching for "elongated engagement rings" now include marquise alongside oval and pear. The other driver is cost. A 12x6mm marquise moissanite reads as a 1.5 carat equivalent but costs about 20% less than an oval of the same visual weight, because marquise cutting waste is lower. For your shop, that makes marquise the value pick for brides who want an elongated look without the oval price tag. If the bride is comparing shapes on hand, our emerald cut bridal elegance guide is the other elongated shape she will try.
What size marquise reads like a 1 carat diamond?
A 10x5mm marquise is roughly 1 carat equivalent. A 12x6mm reads about 1.5. Marquise looks larger than its weight because the eye follows the length.
Does marquise show bow-tie effect like oval?
Yes, sometimes. Moissanite is less prone than diamond because of the higher refractive index, but check the stone under direct light before you ship. Reject stones with a visible bow-tie band.
Can I wear a marquise ring every day?
Yes, with V-prongs and a low setting. Avoid high cathedral mounts that expose the tips to knocks. See our settings for active brides guide.
Is marquise a good choice for a wide finger?
It is the best choice. Marquise adds the most visual length per carat equivalent of any shape.
How to photograph a marquise for your store page
Marquise is the hardest shape to photograph well. Shoot it from the top, not at an angle, because the point asymmetry shows up badly in angled shots. Use a soft box, not direct flash, because direct flash makes the bow-tie effect visible. Place the ring on a light wood surface, not white, because white washes out the stone. We send our buyers a sample photo sheet with every marquise order so your online listings match the in-store piece. If the bride wants to compare on hand, ask her to try the emerald cut next door for contrast before she decides.
Wholesale CTA: HOLYCOME ships marquise moissanite solitaire rings in 10x5, 12x6 and 14x7mm, all at 2.0:1 ratio with V-tip prongs in 14k gold. MOQ 6 rings per size. Ask for the marquise sample pack this quarter.
Frequently Asked Questions
What ring sizes can you supply in bulk?
US sizes 5–12 including half sizes. Send a size breakdown with your order and we cast to that curve; comfort-fit inner bands reduce resize requests.
Can I order a mixed size run instead of one size?
Yes. Mixed runs are standard for wholesale: specify quantity per size and we pack and label by size at no extra labor cost.
What is the MOQ for custom ring designs?
50 pieces per design for existing molds; 100–300 pieces when a new mold or CAD model is required.
How should I price rings for retail margin?
Most partners use a 3–4x markup on FOB cost for sterling and 2.5–3x for moissanite solos, which keeps landed cost under 30% of retail.
Send your spec sheet — stone, cut, size, plating and quantity — and we will return a costed timeline.
Ask the workshop



