Wedding Rings & Bands
Curved Wedding Bands Around an Irregular Setting
A retailer in Madrid showed us a customer's wedding set on a display hand. The engagement ring was a cathedral-set oval. The wedding band was a straight half-eternity. Between them was a visible wedge of daylight. The customer thought it was a defect. The associate had not ordered a curved band, and the gap was unfixable. That gap is the entire reason curved (contour) wedding bands exist, and why a bridal case needs them in stock rather than by special order.
Why irregular settings need a curved band
A cathedral setting lifts the engagement ring's center off the finger, so the shank kicks up at the shoulders. A halo setting spreads a wide rim of stones. A pear, marquise or emerald shape leaves uneven edges. In every case, a straight band cannot sit flush; it rocks, gaps, and eventually wears on the adjacent ring. A curved (contour) band is cut with a scallop that follows the underside of the engagement setting, so the two rings touch along their whole facing edge. This is the flush-fit logic detailed in how rings stack on one finger.
The three curve shapes your tray needs
Contour (moderate curve): a gentle arc that meets a standard cathedral solitaire. The workhorse SKU; fits about 70% of settings. Notched (deep curve): a sharper dip for a high cathedral or a wide halo, where the band must tuck under the setting. Shadow (gap curve): a smaller curve that leaves a deliberate light gap, sold as a design choice for low-profile solitaire settings. Stock all three so a customer can match the curve to her existing ring, rather than expecting one band to fit everything.
Matching the curve to the stone shape
A marquise or pear setting has tapered ends; a band curved along that taper sits tighter than a generic contour. An emerald or oval cathedral needs a deeper notch. A halo needs a band wide enough to mirror the halo's rim without colliding. When you stock samples, pair each curve with the matching setting type so customers can try the actual combination. This is the same geometry that makes marquise settings pair poorly with straight bands.
Stone continuity on a curved band
A curved band can carry pavé stones, but the curve changes the angle of each stone seat. Poorly tooled curves twist the stones outward so they catch light awkwardly. Buy curved bands where the stones remain perpendicular to the finger despite the bend. For durability on a curved, daily-wear piece, prefer shared-prong pavé over delicate micro-pave (see pave vs micro-pave durability).
Measuring a customer's existing setting
When a customer arrives with an engagement ring she already owns, the curved band cannot be guessed. Measure three things: the height the setting lifts off the finger, the width of the shoulder gap, and the profile where the band must meet. A quick visual match against your three curve samples is usually enough, but a customer with a high cathedral should try the notched band specifically. Taking two minutes to match the curve on the demo hand prevents the most common bridal return: a band that rocks.
Metal and width continuity
A curved band should match the engagement ring's metal and shank width, or the curve looks like an afterthought. A white-gold cathedral with a rose-gold curved band is a deliberate two-tone choice; a white-gold cathedral with a mismatched yellow-gold band looks like a mistake. Keep width within 0.2mm of the existing shank so the two rings sit as one. This continuity is invisible when done right and obvious when done wrong.
What is the difference between a contour and a notched band?
A contour band has a shallow, smooth arc for a standard cathedral. A notched band has a deeper, sharper dip for a high cathedral or wide halo that the contour cannot tuck under.
Can a curved band be worn alone?
Yes, a well-designed contour band is attractive on its own, but its curve is most visible beside the engagement setting. Sell it as part of the set.
Do curved bands cost more than straight bands?
Slightly, because tooling the scallop is extra work. The premium is justified because it solves a real fit problem; a straight band that gaps is a return.
What if the customer already owns an engagement ring?
Ask her to bring the ring (or measure the setting's shoulder profile). Match the curve to her exact setting rather than guessing. This is where a tray of three curve shapes earns its space.
Wholesale note: HOLYCOME tooled contour, notched and shadow curved bands in matched 2.0-2.2mm shank widths, so they tuck flush under cathedral, halo, marquise and pear settings. If your store wants to stop the daylight-gap returns, request a three-curve sample tray and match each to a demo setting. Build the set with matching wedding bands, keep metal consistent with metal guidance, and document plating against EU REACH nickel rules.
Frequently Asked Questions
What ring sizes can you supply in bulk?
US sizes 5–12 including half sizes. Send a size breakdown with your order and we cast to that curve; comfort-fit inner bands reduce resize requests.
Can I order a mixed size run instead of one size?
Yes. Mixed runs are standard for wholesale: specify quantity per size and we pack and label by size at no extra labor cost.
What is the MOQ for custom ring designs?
50 pieces per design for existing molds; 100–300 pieces when a new mold or CAD model is required.
How should I price rings for retail margin?
Most partners use a 3–4x markup on FOB cost for sterling and 2.5–3x for moissanite solos, which keeps landed cost under 30% of retail.
Send your spec sheet — stone, cut, size, plating and quantity — and we will return a costed timeline.
Ask the workshop



