Factory-direct bridal jewelry, shipped to the USA

Wedding Rings & Bands

Wedding Rings & Bands B2B: MOQ, Mixed Designs and the Real First Order

9 November 2026 · 10 min

Step 01

MOQ, Mixed Designs and the Real First Order

A US bridal chains and Etsy-adjacent studios came to us after 600 wedding Rings and Bands from a trading company produced 11 rejects in the first inspection. The defect was not cosmetic: flat bore had drifted far enough that the buyer's own bench could not correct it without recutting.

That rejection was avoidable at the drawing stage. flat bore belongs on the spec sheet next to the stone size, not in the claim email three weeks after arrival. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Wedding Rings & Bands wholesale product photo from the HOLYCOME line in Wuzhou

Our rebuild kept the buyer's retail price and changed four numbers on the bench. The next run cleared inspection because the specification traveled with the tray, not with a phone call. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Step 02

What American buyers Check Before They Sign

Most quotes describe the wedding Rings and Band and skip the part that determines the buyer's margin. Those four lines are listed below with the trade default beside our standard. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Flat Bore on wedding Rings and BandsInspected visually at the trayGauntlet check on every piece, limit written in the specReturns inside 60 days of wear
Width Drift After Polish on wedding Rings and BandsBatch dependent, not loggedThickness and tension logged per lotComplaint after the second season
Eternity Sizing Limits on wedding Rings and BandsEstimated from nominalGauged per size with go/no-go toolsResize queue and reship cost
Tolerance stack-up on wedding Rings and BandsQuote states nominal onlyWorst-case band published per SKUFreight and duty drift

Write these four into the purchase order and the argument after delivery becomes arithmetic rather than recollection. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Step 03

Where USD 42-240 Per Piece Actually Goes

Buyers assume the stone dominates the cost of a wedding Rings and Band. At wholesale it is closer to a quarter, and the labor line is where two quotes for the same drawing diverge by double digits. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Wedding Rings & Bands close-up of setting and finish, HOLYCOME factory sample
Cost lineShareWhat moves it
Base metal or alloy for wedding Rings and Bands32%Alloy choice and casting yield
Stone or melee for wedding Rings and Bands23%Sieve range and lot batching
Setting and finishing labor for wedding Rings and Bands21%Jig design and bench minutes
Plating, polish and QC for wedding Rings and Bands14%Per-tray versus per-piece checks
Packaging and freight for wedding Rings and Bands10%Box grade and DDP versus FOB

The cheapest quote for wedding Rings and Bands usually hides its saving in the plating line and the stone grade. Both show up in the second season, not the first. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Step 04

The Three Failures We See Most in Incoming Samples

flat bore

A flat inside profile casts faster and reads as a sharp edge on a size 4.5 finger. Comfort radius is 40 seconds of finishing per band and it is the first thing skipped.

The commercial effect is resize labor plus a second freight leg, typically USD 11-18 per band. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return.

width drift after polish

Polishing removes 0.04-0.10 mm from the outside face. A run that checks width before polish ships a band 0.08 mm narrower than the approved sample.

Our countermeasure is a gauge and a written limit. It adds about 18 seconds per piece and removes the defect from the run rather than from the carton.

eternity sizing limits

A full-eternity band cannot be resized without resetting stones. Quoting it as a sizeable product is how a buyer absorbs a reset cost on the first exchange.

In a 600-piece run this typically shows on 11 of pieces. Catching it means measuring width at the tray level, not inspecting the finished carton.

Step 05

MOQ, Mixed Designs and the Real First Order

This is where wedding Rings and Bands stops being a commodity and starts being a supply relationship.

We run this check per tray rather than per carton because the defect that matters on bands is the one that repeats. A single odd piece is noise; a pattern across one tray is a process problem and it will be in every tray made after it.

The report the buyer receives states the count per tray, the measured average and the outlier count for wedding Rings and Bands. It is deliberately unglamorous, and it is the document that settles most disputes before they start.

Step 06

How a Repeat Order Gets Built

The calendar below is what we quote on a 600-piece run of wedding Rings and Bands. It starts when the spec is signed, not when the deposit clears. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

  1. Spec sheet signed before casting: court, tolerances, plating thickness and packing format.
  2. Sample in 3-5 working days from stock components, or about 20 days if a new model is required.
  3. Production photos at three checkpoints: raw cast, post-polish, post-set, with buyer approval at each.
  4. Bulk in 15-20 days under 500 pieces; custom tooling runs 25-30 days.
  5. Pre-shipment QC report with per-tray counts and a retained reference tray for disputes.

MOQ is 50 pieces per design, low enough to test a category and high enough to keep the casting line accountable. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Step 07

Sample to Container: The Real Calendar

For wedding Rings and Bands at this price band, the honest answer is a range rather than a point, and the range has a reason.

The buyers who get the most out of bands treat the first order as a measurement, not as a purchase. They buy a small run, measure the four numbers that matter, and then commit.

We support it directly on wedding Rings and Bands: a 50-piece test run per design, the same gauge standard as a bulk order, and the same retained tray. Small does not have to mean loose.

Step 08

Carton Cube, Duty and the Freight Line That Surprises Buyers

Buyers ask it in the first call about wedding Rings and Bands and rarely get a number they can put in a spreadsheet.

Buyers who get this wrong on bands usually get it wrong in the first order and correct it in the second. The cost of that correction is rarely the money; it is the four to six weeks of shelf time lost while a replacement run of bands is scheduled behind other orders.

Our approach is to write the rule into the wedding Rings and Bands spec sheet before casting, then test it on the first tray. A rule that only exists in an email is not a rule, and a rule that is not tested is a hope.

Step 09

Carton Cube, Duty and the Freight Line That Surprises Buyers

Nobody quotes it for wedding Rings and Bands until something goes wrong, which is exactly why it belongs in the first email.

The commercial version of this question for bands is simple: what does a failure cost the buyer, and who pays it. In our terms the answer is a replacement inside the same order cycle, with the retained reference tray as the arbiter.

That clause matters more than a discount on bands. A 4% lower unit price disappears on the first rejected tray; a written responsibility clause does not.

Step 10

What This Means for a First Order

The point of a small first run is not the margin. It is finding out whether the supplier's paperwork survives contact with the actual goods. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

The first order is the cheapest inspection a buyer will ever run, because the volume is small enough to check every tray by hand. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Step 11

Freight, Duty and the Arrival Check

Sea freight costs roughly a third of air and takes three times the transit, which only makes sense for an SKU already selling in the US market. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

FOB is the default and DDP is the option. Buyers new to the US market usually take DDP once and then switch after they see the breakdown. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

The arrival check is three steps: count cartons against the packing list, weigh a sample tray, and measure ten pieces against width and inside diameter consistency across a 200-piece run. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

Step 12

Frequently Asked Questions

What is the minimum order for wedding Rings and Bands?

50 pieces per wedding Rings and Band. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 we cannot keep the gauge check independent of the shift, which is the part buyers actually pay for on wedding Rings and Bands.

How long does a reorder of the same wedding Rings and Band take?

12-15 days for wedding Rings and Bands, because the model, the gauge set and the signed spec stay in our system. A first run is longer: 3-5 days for a stock-component sample, about 20 days if a new model is needed, then 15-20 days for bulk under 500 pieces.

Do you supply certificates for wedding Rings and Bands?

metal assay report per lot for wedding Rings and Bands. Below that threshold we supply a batch report plus per-piece measurement of width, which is what most resellers need at the counter.

What finish do you use on wedding Rings and Bands, and how thick is it?

Rhodium at 0.20 micron minimum on white wedding Rings and Bands, with a palladium strike layer so wear-through reads white rather than yellow. Thickness is logged per lot and appears on the QC sheet, not only in the brochure.

How do you handle a rejected tray of wedding Rings and Bands?

We replace or credit inside the same order cycle. The retained reference tray decides: if flat bore shows on our retained wedding Rings and Band we own it, and if it appeared in transit we split the assay cost and file with the carrier. A typical exposure on wedding Rings and Bands is resize labor plus a second freight leg, typically USD 11-18 per band.

Step 13

Next Step

Send one drawing or one competitor sample with your target landed cost. We answer with a tolerance sheet, a cost breakdown and a production calendar in two business days. For wedding Rings and Bands in this band the rule is the same on every tray of the run, not only on the first.

HOLYCOME runs this line from Wuzhou, Guangxi, through Wuzhou HengliLai Jewelry Co., Ltd. Output is about 60,000 pieces a month across wedding Rings and Bands and adjacent categories. service@holycome.com or WhatsApp +86 133 7744 7107.

Related reading: Bridal Sets Wholesale: Sample to Container: The Real Calendar - HOLYCOME Bracelets & Bangles Wholesale: Alloy, Karat and the Cost of a Color Change - HOLYCOME

Put this into a quotation

Send your spec sheet — stone, cut, size, plating and quantity — and we will return a costed timeline.

Ask the workshop

← Back to all articles

Related Jewelry Guides

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .