Factory-direct bridal jewelry, shipped to the USA

Bridal Sets

Bridal Sets: Custom: From CAD to Production Without Losing the Design - GemWSL

16 November 2026 · 4 min

A custom bridal sets fails in one of two places: the CAD is approved before the stone is sourced, or the bench 'adjusts' the model to make it castable. Both are avoidable with a staged approval.

Step 01

Stage one: the brief that survives translation

Give the factory five inputs: reference image, stone size in millimetres, metal and karat, finger size or chain length, and the retail price ceiling. Without the price ceiling, the CAD comes back beautiful and unmakeable at your margin.

Ask for a dimensioned drawing, not a render. A render hides the gallery height and the prong thickness, which are the two places a design fails.

Seal the approved sample in a bag with the PO number. It is the only physical record that settles a claim without an argument.

Step 02

Stage two: CAD approval with three checkpoints

Checkpoint one is stone seat depth: the stone must sit below the prong tips. Checkpoint two is minimum wall thickness at the shank. Checkpoint three is the casting allowance, usually 3 to 5 percent shrink.

Approve in writing at each checkpoint. A single 'looks good' message on bridal sets is how a 1.8 mm shank becomes 1.4 mm after polishing.

StageDeliverableApproval gate
BriefDimensioned drawingStone size, metal, ceiling
CADSTEP file, wall thicknessWritten sign-off
Wax or printPhoto of the modelSeat and prong check
First articleOne cast piecePorosity and size check
BatchProduction runAQL inspection

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Photograph the first article before the batch runs. A shifted seat or a short prong is cheapest to fix at one piece.

Step 03

Stage three: wax, cast and the first article

Ask for a photo of the wax or the resin print before casting. Ask for the first cast piece before the batch. That first article is where you catch porosity, a shifted seat or a prong that is too short.

Only after the first article passes should the batch run. Skipping it saves three days and costs a full lot.

Step 04

Stage four: who owns the model

The CAD file is an asset. Put ownership in writing: the buyer owns the model after the mold fee is paid, and the factory will not reuse it for another client.

Without that clause, your custom bridal sets can appear in another buyer's catalog two seasons later.

In practice, the first lot answers more than the quote does. Weigh ten pieces, measure five stones and rub three contact points, and the specification stops being a claim.

Step 05

What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Give five inputs, including the price ceiling.
  • Approve a dimensioned drawing, not a render.
  • Check stone seat depth and wall thickness.
  • Photograph the wax before casting.
  • Put CAD ownership in the contract.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

Step 06

Frequently Asked Questions

How long does a custom bridal sets CAD take?

Three to seven days for a first model, longer if the stone has to be sourced first.

Who should own the CAD file?

The buyer, after paying the mold fee. Ask for the clause in writing before the first order.

Can I reuse the mold for another size?

Often yes, with a size adjustment. Ask whether the factory charges a new mold for a size change.

Why does the cast piece come out smaller?

Casting shrink, typically 3 to 5 percent, plus polishing loss. The CAD should carry the allowance.

What if the first article fails?

Fix the model, re-cast, and do not release the batch. A failed first article is the cheapest failure you will get.

How many suppliers should I keep?

Two approved sources for the top three designs, one for the tail. The second source is what keeps pricing honest.

Send the bridal sets reference image and stone size. We return a dimensioned CAD, a first-article photo and the mold fee quoted separately. See the full range at GemWSL.

Buyers who get consistent lots are not luckier. They wrote the spec down and checked the first carton against it.

Put this into a quotation

Send your spec sheet — stone, cut, size, plating and quantity — and we will return a costed timeline.

Ask the workshop

← Back to all articles

Related Jewelry Guides

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .